Provide Fortinet NSE6_FSW-7.2 Practice Test Engine for Preparation
Detailed New NSE6_FSW-7.2 Exam Questions for Concept Clearance
NEW QUESTION # 24
Exhibit.
Which configuration change will allow the managed FortiSwitch to accept SNMP requests from any source?
- A. Create a new local access profile for SNMP only.
- B. Configure an SNMP host to send SNMP traps.
- C. Enable SNMP on the internal interface of the switch.
- D. Add SNMP service on the management interface of the switch.
Answer: B
NEW QUESTION # 25
Refer to the exhibits.
Port1 and port2 are the only ports configured with the same native VLAN 10.
What are two reasons that can trigger port1 to shut down? (Choose two.)
- A. port1 was shut down by loop guard protection.
- B. STP triggered a loop and applied loop guard protection on port1.
- C. An endpoint sent a BPDU on port1 that it received from another interface.
- D. Loop guard frame sourced from port 1 was received on port 1.
Answer: B,C
NEW QUESTION # 26
Which statement about using MAC, IP, and protocol-based VLANs on FortiSwitch is true?
- A. Endpoints are required to use the same FortiSwitch port to remain members of the VLAN.
- B. FortiSwitch uses only the Ethernet type to assign traffic to VLANs.
- C. lt is a scalable and secure solution in comparison to other Layer 2 security measures.
- D. It provides benefits that can be obtained when using 802.1X authentication.
Answer: D
NEW QUESTION # 27
FortiGate is unable to establish a tunnel with the FortiSwitch device it is supposed to manage Based on the debug output shown in the exhibit, what is the reason for the failure?
- A. DTLS client hello had the incorrect pre-shared key.
- B. The handshake process timed out before FortiSwitch responded.
- C. The CAPWAP tunnel failed to come up due to a mismatch in time.
- D. FortiSwitch has disabled FortiLink and is only managed as a standalone.
Answer: C
NEW QUESTION # 28
Which statement about the configuration of VLANs on a managed FortiSwitch port is true?
- A. FortiSwitch VLAN interfaces are created only when FortiSwitch is managed by Forti-Gate.
- B. Allowed VLANS expand the collision domain to the port.
- C. The native VLAN is implicitly part of the allowed VLAN on the port.
- D. Untagged VLANs must be part of the allowed VLANs: ingress and egress.
Answer: C
NEW QUESTION # 29
What feature can network administrators use to segment network operations and the administration of managed FortiSwitch devices on FortiGate?
- A. FortiLink split interface
- B. Multi-chassis link aggregation trunk
- C. FortiGate multi-tenancy
- D. FortiGate clustering protocol
Answer: C
NEW QUESTION # 30
Refer to the exhibit.
The exhibit shows the current status of the ports on the managed FortiSwitch. Access-1.
Why would FortiGate display a serial number in the Native VLAN column associated with the port23 entry?
- A. port23 is configured as the dedicated management interface.
- B. Ports connected to adjacent FortiSwitch devices show their serial number as the native VLAN.
- C. A standalone switch with the shown serial number is connected on port23.
- D. port23 is a member of a trunk that uses the Access-1 FortiSwitch serial number as the name of the trunk.
Answer: C
NEW QUESTION # 31
Which feature should you enable to reduce the number or unwanted IGMP reports processed by the IGMP querier?
- A. Enable the IGMP flood setting on the static port for all multicast groups.
- B. Enable the IGMP flood reports setting on the mRouter port.
- C. Enable IGMP flood unknown multicast traffic on the global setting.
- D. Enable IGMP snooping proxy.
Answer: D
NEW QUESTION # 32
Which Ethernet frame can create Layer 2 flooding due to all bytes on the destination MAC address being set to all FF?
- A. The anycast Ethernet frame
- B. The multicast Ethernet frame
- C. The unicast Ethernet frame
- D. The broadcast Ethernet frame
Answer: D
NEW QUESTION # 33
Which two types of Layer 3 interfaces can participate in dynamic routing on FortiSwitch? (Choose two.)
- A. Switch virtual interfaces
- B. Detected management interfaces
- C. Loopback interfaces
- D. Physical interfaces
Answer: A,C
NEW QUESTION # 34
Exhibit.
port24 is the only uplink port connected to the network where access to FortiSwitch management services is possible. However, FortiSwitch is still not accessible on the management interface. Which two actions should you take to fix the issue and access FortiSwitch? (Choose two.)
- A. You must add port24 native VLAN as an allowed VLAN on internal.
- B. You should use VLAN ID 4094 as the native VLAN on port24.
- C. You must allow VLAN ID 4094 on port24, if management traffic is tagged.
- D. You must add VLAN ID 200 to the allowed VLANS on internal.
Answer: B,C
NEW QUESTION # 35
Which two statements about the FortiLink authorization process are true? (Choose two.)
- A. The administrator must manually pre-authorize FortiGate on FortiSwitch by adding the FortiGate serial number.
- B. FortiSwitch requires a reboot to complete the authorization process.
- C. A FortiLink frame is sent by FortiGate to FortiSwitch to complete the authorization.
- D. FortiLink authorization sets the FortiSwitch management mode to FortiLink.
Answer: C,D
NEW QUESTION # 36
Refer to the exhibit.
The profile shown in the exhibit is assigned to a group of managed FortiSwitch ports. and these ports are connected to endpoints which are powered by PoE. Which configuration action can you perform on the LLDP profile to cause these endpoints to exchange PoE information and negotiate power with the managed FortiSwitch?
- A. Create new a LLOP-MEO application type to define the PoE parameters.
- B. Define an LLDP-ME0 location 10 to use standard protocols for power.
- C. Assign a new LL0P profile to handle different LLDP-ME0 TLVs
- D. Add power management as part of LLDP-MED TLVs to advertise.
Answer: D
NEW QUESTION # 37
Which interfaces on FortiSwitch send out FortiLink discovery frames by default in order to detect a FortiGate with an enabled FortiLink interface?
- A. The ports with auto-discovery enabled by default are dependent upon the FortiSwitch model.
- B. No ports are enabled by default for auto-discovery. This must be configured under config switch interface.
- C. All ports have auto-discovery enabled by default.
- D. The last four switch ports on FortiSwitch have auto-discovery enabled by default.
Answer: C
NEW QUESTION # 38
Refer to the exhibit.
Which two statements best describe what is displayed in the FortiLink debug output shown in the exhibit? (Choose two.)
- A. FortiSwitch is ready to push its new hostname to FortiGate.
- B. FortiSwitch is sending FortiLink heartbeats to FortiGate.
- C. FortiSwitch is in a waiting state to join the stack group on FortiGate.
- D. FortiSwitch is discovered and authorized by FortiGate.
Answer: B,D
NEW QUESTION # 39
What can an administrator do to maintain a FortiGate-compatible FortiSwitch configuration when changing the management mode from standalone to FortiLinK?
- A. Register FortiSwitch to FortiSwitch Cloud to save a copy before managing with FortiGate.
- B. Use a migration tool based on Python script to convert the configuration.
- C. FortiGate automatically saves the existing FortiSwitch configuration during the FortiLink management process.
- D. Enable the FortiLink setting on FortiSwitch before the authorization process.
Answer: A
NEW QUESTION # 40
Refer to the exhibits
Traffic arriving on port2 on FortiSwitch is tagged with VLAN ID 10 and destined for PC1 connected on port1. PC1 expects to receive traffic untagged from port1 on FortiSwitch.
Which two configurations can you perform on FortiSwitch to ensure PC1 receives untagged traffic on port1? (Choose two.)
- A. Add the MAC address of PCI as a member of VLAN 10.
- B. Add VLAN ID 10 as a member of the untagged VLANs on port1.
- C. Enable Private VLAN on VLAN 10 and add VLAN 20 as an isolated VLAN.
- D. Remove VLAN 10 from the allowed VLANs and add it to untagged VLANs on port1.
Answer: A,B
NEW QUESTION # 41
Refer to the exhibits.
You are asked to ensure that managed FortiSwitch devices are reachable by other devices, such as SNMP and other management tools across your network.
Which setting must you configure to ensure traffic from other devices in the network reaches FortiSwitch?
- A. Recreate the FortiLink interface with a nonaggregate setting.
- B. Change the FortiLink interface IP address and DHCP server address range.
- C. Select a specific default gateway provided to FortiSwitch as an upstream device.
- D. Enable NAC settings to select the onboarding VLAN.
Answer: B
NEW QUESTION # 42
Refer to the exhibit.
Core-1 and Access-1 are managed and authorized by FortiGate-1. which uses port4 as the FortiLink interface. After FortiGate authorizes and manages Core-2. Port1 status becomes STP discarding.
Why is port1 in the discarding state?
- A. Core-1 and Core-2 do not have MCLAG configuration.
- B. Access-1 is the root bridge and can only have one root port.
- C. port1 on Core-2 is discarding only management traffic.
- D. Core-2 has the lowest bridge priority.
Answer: A
NEW QUESTION # 43
Refer to the exhibit.
What two conclusions can be made regarding DHCP snooping configuration? (Choose two.)
- A. FortiSwitch is configured to trust DHCP replies coming on FortiLink interface.
- B. Global configuration for DHCP snooping is set to forward DHCP client requests on all ports in the VLAN.
- C. Maximum value to accept clients DHCP request is configured as per DHCP server range.
- D. DHCP clients that are trusted by DHCP snooping configured is only one.
Answer: A,D
NEW QUESTION # 44
Which QoS mechanism maps packets with specific CoS or DSCP markings to an egress queue?
- A. Rate limiting for egress traffic
- B. Classification for ingress traffic
- C. Marking for ingress traffic
- D. Queuing for egress traffic
Answer: B
NEW QUESTION # 45
To enhance service in emergency situations, to which LLDP-MED Type-Length-Values does Forti-Switch advertise to IP phones?
- A. Location
- B. Inventory management
- C. Network policy
- D. Power management
Answer: B
NEW QUESTION # 46
......
Fortinet NSE6_FSW-7.2 certification exam is an essential certification for professionals who want to validate their skills and knowledge in FortiSwitch 7.2 technology. Fortinet NSE 6 - FortiSwitch 7.2 certification is recognized globally and provides you with a competitive advantage in the job market. To prepare for the exam, you should have a deep understanding of FortiSwitch 7.2 technology and be familiar with the Fortinet NSE program. Fortinet offers a variety of training courses and resources to help you prepare for the exam.
NSE6_FSW-7.2 2024 Training With 56 QA's: https://freedumps.testpdf.com/NSE6_FSW-7.2-practice-test.html
